AFIDA – Indicated Cetane Number Analyser - SA6000-0

Features

• Indicated Cetane Number by CVCC
• Range 35-85 ICN
• Highly automated with auto sampler
• Primary Reference Fuel Calibration
• No bias correction to engine values
• Excellent precision, minimal giveaway
• Easy to use, suitable for 24/7 operation
• Load and go

AFIDA Ambered Vials (pack of 100) - SA6003-001

Features

• Pack of 100 ambered vials
• For use with the AFIDA SA6000-0)

AFIDA Septums for Sample Vials (pack of 100) - SA6003-002

Features

• Pack of 100 vials
• For use with ambered sample vials SA6003-001

Verification Fluid (pack of 4) - SA6009-0

Features

• Pack of 4 x 40 ml verification fluid vials
• For use with the AFIDA SA6000-0

Seta Silver and Copper Corrosion Bath – 11405-0

Features

• Ambient +5 to 150 °C
• 22 litre bath
• Six test stations
• Programmable digital temperature controller
• Digital timer
• Over temp cut out & liquid level float switch
• Maximum liquid level outlet fitting
• Small footprint

Seta Copper Silver Block Bath - 11310-0

Features

• Dry heating for up to four test samples
• Holds four 25x150 mm test tubes
• Operator selected test set point temperature
• Stability ±0.1 °C

Seta Oxi-Cor Bath - 15550-3

Features

• Stainless steel water or oil bath
• Ambient +5 to 150 °C temp range
• Four test stations (Three when used for Oxidation tests)
• Copper/Silver Corrosion and Oxidation tests
• Optional automatic pressure monitoring
• Integral over-temperature and low fluid level protection devices

Salt in Crude Analyser - 99700-6

Features

• Pre calibrated for immediate use to ASTM D3230
• Salt concentration values displayed automatically
• No need for mixing of salt standards
• Typical test time of less than 30 seconds
• Calibration modes allow verification using user standards
• Fully portable

H2S Analyser with VPP - SA4000-4

Features

• Measurement range from 0-250 mg/kg H2S (0-250 ppm H2S) in the liquid phase
• Vapour Phase Processor proven to eliminate effects of chemical interference
• A non chemical method, no wet chemistry involved
• Small lab bench footprint, fully portable operation
• Suitable for monitoring residual marine fuel blends, Crude Oil, refinery feedstock components, cargoes & products in the distribution system
• Critical Measurement method for Product Safety and Release

Oil Test Centrifuge – 4 place - 90000-3

Features

• Specially designed for testing oils
• Heated chamber, ambient to 80 °C
• 4 place swing out rotor
• Optional trolley
• Pre-heat facility to ensure bowl is at test temperature prior to test
• Universal buckets for 12.5 ml, 6 and 8 inch glassware
• Microprocessor control with 99 memories
• 6 place centrifuge available (90100-0)

SetaVap4 Automatic Vapour Pressure Analyser - 80600-2

Features

• Rapid, automatic testing
• Simple test procedure
• Compact, rugged design for portable or laboratory use
• Real time display of test progress and storage for 500,000 results
• LIMS connectivity and RS232C serial port, results can be saved to USB or transferred via QR code
• Statistical Quality Control (SQC) software to analyse results to conform to ASTM D6299
• Test multiple temperatures and multiple V/L ratios (ASTM D6377)

FAME in Jet Fuel – FIJI - SA5000-2

Features

• Measures presence of all FAME types C8-C22
• Approved for co-processed fuels
• Analysis time 20 minutes
• 50 ml sample volume
• No hydrocarbon cleaning solvents required
• Laboratory and field instrument
• Suitable for untrained operators

FIJI MF – FAME in MultiFuels - SA5200-0

Features

• Measures presence of all FAME types C8-C22
• Analysis time 20 minutes
• 50 ml sample volume
• Approved for co-processed fuels
• No hydrocarbon cleaning solvents required
• Laboratory and field instrument
• Suitable for untrained operators

SetaCheck Biodiesel Plus - SA5550-0

Features

• 0.1% to 80% measurement range
• No dilution required, samples measured directly
• Internal rechargeable battery
• Bright backlit screen displays the Biodiesel concentration (% by volume)
• Can store both a factory and a local calibration
• User calibration available via PC software
• Includes optional built-in 9:1 dilution mode
• Correlates with EN 14078

PM-93 Pensky-Martens Flash Point Tester - 35000-0

Features

• Easy operation
• Superior safety
• Patented ‘SafeFlash’ auto fire extinguisher
• Complies with ISO 2719 annex b
• Gas or electronic ignition
• Memory storage for 2000 results
• Compact footprint
• Statistical Quality Control software

Setaflash Series 3 Flash Point Tester - 30000-3

Features

• 1 minute test, 2 ml sample
• Ambient to 300 °C
• Simple test procedure
• Compact, portable and rugged design
• Automated flash detection
• Automatic barometric pressure correction
• USB port and result storage
• Low cost of purchase and maintenance

Setaflash Series 3e ActiveCool Flash Point Tester - 33220-0

Features

• Flash / No Flash & Ramp modes
• Electric ignitor
• 10 to 135°C temperature range
• Less than 2 minute test
• Small sample size (2 or 4ml)
• Automatic flash detection
• Electronic peltier cooling
• Portable operation

Setaflash Series 8 ActiveCool Flash Point Tester - 82100-2

Features

• -30 °C to 135 °C, no external cooling
• 2 ml sample, 1 minute test
• Electric ignition (gas models available)
• Automated flash detection
• Ramp mode for unknown samples
• Fire detection (alarm and relay)
• Peltier heating and cooling
• Automatic barometric pressure correction

H2S Analyser with VPP - SA4000-4

Features

• Measurement range from 0-250 mg/kg H2S (0-250 ppm H2S) in the liquid phase
• Vapour Phase Processor proven to eliminate effects of chemical interference
• A non chemical method, no wet chemistry involved
• Small lab bench footprint, fully portable operation
• Suitable for monitoring residual marine fuel blends, Crude Oil, refinery feedstock components, cargoes & products in the distribution system
• Critical Measurement method for Product Safety and Release

H2S Vapour Phase Processor Cartridge (pack of 100) - SA4017-100

Features

• Pack of 100 filter cartridges
• One to be used per test
• For use with the Vapour Phase Processor (SA4015-0)

H2S Verification and Calibration Gas (110 litre) - SA4001-001

Features

• 110 litre canister of 25 ppm Hydrogen Sulfide
• Verification is required every 30 days
• Used to calibrate and verify the H2S Analyser (SA4000-3)

IP 570 PTS Quarterly Membership - SA4032-0

Features

• A statistical quality assurance program available in monthly cycles
• Enables laboratories to evaluate their performance for testing liquid phase
• Ability to demonstrate compliance with laboratory accreditation requirements (ISO 17025)
• World-wide inter-laboratory comparison of test results and performance
• Identify any potential equipment or operational bias
• Provides added confidence to laboratory staff and customers
• Reduced potential for dispute

Herschel Emulsifier - 96700-2

Features

• 4 independently controlled test stations
• Multiple operator safety features
• Automated test sequence
• No removal of the paddles required
• Guaranteed paddle rotation speed
• Non-reflective enhanced LED lighting
• Small footprint
• Intuitive software package

Air Release Value System - 15840-0

Features

• Integrated solution
• Multi-station sample handling
• Automated and integrated density monitoring
• Automatic result calculation
• Results storage for over 10,000 tests
• Full LIMS connectivity
• Quick connectors for ease of sample handling
• Automated calibration procedure

AvCountHV - SA1110-0

Features

• High viscosity, up to 1500 mm2/s at 20 °C
• ISO 11171 calibration
• Cumulative counts/ml
• ISO 4406 cleanliness codes
• Dilution ratio calculation
• Real time display of test progress
• LIMS, network and VNC connectivity
• In-field verification and calibration

PM-93 Pensky-Martens Flash Point Tester - 35000-0

Features

• Easy operation
• Superior safety
• Patented ‘SafeFlash’ auto fire extinguisher
• Complies with ISO 2719 annex b
• Gas or electronic ignition
• Memory storage for 2000 results
• Compact footprint
• Statistical Quality Control software

Oxi Solid Block Bath 4 Way - 16670-0

Features

• 4 position
• Dry block
• Digital temperature control
• Over temperature cut out
• Pressure in the vessel can be monitored automatically with the Seta Auto-Oxi Control System (15452-2)
• Small footprint

Water Separation Instrument- WSI Analyser - SA9000-0

Features

Features

• Fully automated test procedure
• Suitable for untrained operators
• Automated sample mixing for increased accuracy
• Rapid test, no warm up time
• Internal data storage and USB output
• Substantial consumable cost and waste saving
• Field calibration, no down time

Seta Auto-Oxi Control System - 15452-2

Features

• Suitable for use with a range of pressure vessels
• Connects to Seta Pressure Transducers via USB hub
• Automatic breakpoint determination
• Connects to Computer via a USB cable
• Incorporates purge and leak test
• With Digital USB thermometer
• Graphical display

WSI Filter Assembly Jig - SA9015-0

Features

Features

• Cost effective
• Easy to use
• Environmentally friendly
• Easily portable

Seta Auto-Oxidation Stability Bath - 15400-5

Features

• Operating temperature 100°C
• Water Bath with integral condenser
• 4 test stations
• Cold plunge bath
• Seta Auto-Oxi Automatic Pressure Monitoring
• Integral vessel charge system
• Constant level device

WSI Reference Fluid Base, 97.5 to 100 WSI - SA9004-0

Features

Features

• Produced in accordance with IP 624 Annex B and ASTM D8073 Appendix X1
• A surfactant-free aviation turbine fuel
• Supplied with full documentation including Safety Data Sheet (SDS)
• 2 year shelf life from date of manufacture
• Use directly and to make reference fluids to cross-check test method performance
• Supplied with a certificate of measurement

WSI Replacement Filters (pack of 50) - SA9001-008

Features

Features

• Single use, individually foil sealed filter material, for ASTM D8073
• A low cost alternative to pre-assembled filter cartridges to help reduce consumable costs
• Re-usable filter cartridge is supplied with each pack
• Easily replaced after each test using the WSI Filter Assembly Tool SA9015-0

Seta Oxi-Cor Bath - 15550-3

Features

• Stainless steel water or oil bath
• Ambient +5 to 150 °C temp range
• Four test stations (Three when used for Oxidation tests)
• Copper/Silver Corrosion and Oxidation tests
• Optional automatic pressure monitoring
• Integral over-temperature and low fluid level protection devices

AvCount3 Particle Counter - SA1100-0

Features

• ISO 11171 calibration
• Cumulative counts/ml
• ISO 4406 cleanliness codes
• Dilution ratio calculation
• Real time display of test progress
• LIMS, network and VNC connectivity
• Programmable alarm limits
• 14 embedded test methods

SetaVap4 Automatic Vapour Pressure Analyser - 80600-2

Features

Features

• Rapid, automatic testing
• Simple test procedure
• Compact, rugged design for portable or laboratory use
• Real time display of test progress and storage for 500,000 results
• LIMS connectivity and RS232C serial port, results can be saved to USB or transferred via QR code
• Statistical Quality Control (SQC) software to analyse results to conform to ASTM D6299
• Test multiple temperatures and multiple V/L ratios (ASTM D6377)

AvCount Lite Particle Counter - SA1800-2

Features

• ISO 11171 calibration
• Cumulative Particles/ml
• ISO 4406 Cleanliness Codes
• Portable, compact instrument
• Online/offline (bottle sample)
• Stand-alone or PC controlled
• Programmable via PC
• Integrated printer

AvCount Lube Particle Counter - SA1900-0

Features

• Calibrated to ISO 11171
• Cumulative Particles/ml
• Up to 200 mm2/s viscosity
• FFKM seals compatible with synthetic oils
• Precise and reliable results
• PC controlled or stand-alone
• Ultra compact rugged, steel case suitable for portable use
• Programmable via PC

Crude Oil Manual Piston Cylinder - 80615-0

Features

Features

• Enables crude oil samples to be taken from a storage tank, rail car or pipeline
• Up to 1380 kPa (200 psi)
• 500 ml sample volume
• Light weight
• Quick set up
• Easy to use
• Dual scale gauge (psi/kPa)

AvCountHV - SA1110-0

Features

• High viscosity, up to 1500 mm2/s at 20 °C
• ISO 11171 calibration
• Cumulative counts/ml
• ISO 4406 cleanliness codes
• Dilution ratio calculation
• Real time display of test progress
• LIMS, network and VNC connectivity
• In-field verification and calibration

SETA-CRM AvCount Verification Material - SA1006-0

Features

• Produced under our ISO 17034 UKAS accreditation
• Characterised in accordance with ISO 11171
• Serves as a Secondary Working Standard (SWS) with a particle distribution traceable to NIST SRM 2806a and 2806d
• Use with Automatic Particle Counters (APCs) calibrated in accordance with ISO 11171 using IP 565, IP 630, and/or ASTM D7619
• Suppled in tamper-evident security packaging with full documentation, including a Safety Data Sheet (SDS)
• 2 year shelf life from the date of manufacture
• 250 mL bottle

AvCount Calibration Material ‘d’ - SA1121-0

Features

• Produced under our ISO 17034 UKAS accreditation
• Homogeneity and variability is checked in accordance with ISO 11171
• Serves as a Secondary Working Standard (SWS) with a particle distribution traceable to NIST 2806d & 8631x
• Use it with Automatic Particle Counters (APCs) calibrated in accordance with ISO 11171
• Supplied in tamper-evident security packaging with full documentation, including a Safety Data Sheet (SDS)
• 2 year shelf life from the date of manufacture
• 250 mL bottle

SETA-CRM FAME

Features

• Produced under our ISO 17034 UKAS accreditation
• Consists of a hydrocarbon sample containing FAME with a certified value
• A gravimetric approach with high-accuracy ISO 17025-calibrated balances is used to ensure precise productio
• This method minimises measurement uncertainties associated with characterisation
• Supplied with full documentation including Safety Data Sheet (SDS)
• 2 year shelf life from date of manufacture

Setavap 2 Vapour Pressure Tester - 81000-2

Features

Features

• Rapid and automatic testing
• "Mini" method uses 3 ml sample size
• Selectable units - kPa or psi
• Results available as Ptot, DVPE, Crude, Pabs

SETA-CRM Pensky-Martens Flash Point

Features

• Produced under our ISO 17034 UKAS accreditation
• Pack of 3 with nominal values of 75 C, 140 C, 225 C
• This hydrocarbon mixture carries certification for Flash Point determination (ASTM D93, IP 34, ISO 2719) and Density measurement (ASTM D4052, IP 365, ISO 12185)
• An Interlaboratory Study characterises the reference material, guaranteeing international traceability and lower-than-average uncertainty
• Laboratories seeking ISO 17025 compliance will find this cost-effective solution simplifies verification processes
• Supplied in a tamper-evident security package with full documentation, including a Safety Data Sheet (SDS)
• 3 year shelf life from the date of manufacture

Vapour Pressure – Certified Reference Material, Pentane 200 ml - 80610-0

Features

Features

• Suitable for verification of Setavap and other mini method instruments
• Determines the vapour pressure of volatile liquid petroleum products, ethanol blends, hydrocarbons and hydrocarbon-oxygenate mixtures

Thermometer Digital: Precision -199 to 199 °C - 51000-0

Features

Features

• -199 to 199 °C
• Excellent precision
• Fast response time
• Compact design
• Traceable calibration in accordance with ASTM E1137 and ASTM E2877 specifications

Digital Thermometer High Range -199 to 300 °C - 51005-0

Features

Features

• High range temperature measurement
• -199.9 to +300ºC
• +/- 0.5 ºC precision
• Compact design
• Traceable calibration in accordance with ASTM E1137 and ASTM E2877

Non Hazardous Thermometer ASTM9C - ASTMST9C

Features

Features

• -5 to +110 ºC
• Non-hazardous
• Same dimensions as traditional Hg thermometers
• Easy to clean up in the event of breakage
• Visually different from Hg (blue filling)

Thermometer ASTMS5C: Low Hazard - ASTMS5CX

Features

Features

• Same dimensions as traditional Hg thermometers
• Easy to clean up in the event of breakage
• Visually different from Hg (blue)
• Classified as non-hazardous for shipping